Something went wrong. Try again.
A fork of https://github.com/crosspoint-reader/crosspoint-reader
Something went wrong. Try again.
3.2 kB · 102 lines
C
at master
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103#pragma once
#include <Arduino.h>#include <InputManager.h>
// Display SPI pins (custom pins for XteinkX4, not hardware SPI defaults)#define EPD_SCLK 8 // SPI Clock#define EPD_MOSI 10 // SPI MOSI (Master Out Slave In)#define EPD_CS 21 // Chip Select#define EPD_DC 4 // Data/Command#define EPD_RST 5 // Reset#define EPD_BUSY 6 // Busy
#define SPI_MISO 7 // SPI MISO, shared between SD card and display (Master In Slave Out)
#define BAT_GPIO0 0 // Battery voltage
#define UART0_RXD 20 // Used for USB connection detection
// Xteink X3 Hardware#define X3_I2C_SDA 20#define X3_I2C_SCL 0#define X3_I2C_FREQ 400000
// TI BQ27220 Fuel gauge I2C#define I2C_ADDR_BQ27220 0x55 // Fuel gauge I2C address#define BQ27220_SOC_REG 0x2C // StateOfCharge() command code (%)#define BQ27220_CUR_REG 0x0C // Current() command code (signed mA)#define BQ27220_VOLT_REG 0x08 // Voltage() command code (mV)
// Analog DS3231 RTC I2C#define I2C_ADDR_DS3231 0x68 // RTC I2C address#define DS3231_SEC_REG 0x00 // Seconds command code (BCD)
// QST QMI8658 IMU I2C#define I2C_ADDR_QMI8658 0x6B // IMU I2C address#define I2C_ADDR_QMI8658_ALT 0x6A // IMU I2C fallback address#define QMI8658_WHO_AM_I_REG 0x00 // WHO_AM_I command code#define QMI8658_WHO_AM_I_VALUE 0x05 // WHO_AM_I expected value
class HalGPIO {#if CROSSPOINT_EMULATED == 0 InputManager inputMgr;#endif
bool lastUsbConnected = false; bool usbStateChanged = false;
public: enum class DeviceType : uint8_t { X4, X3 };
private: DeviceType _deviceType = DeviceType::X4;
public: HalGPIO() = default;
// Inline device type helpers for cleaner downstream checks inline bool deviceIsX3() const { return _deviceType == DeviceType::X3; } inline bool deviceIsX4() const { return _deviceType == DeviceType::X4; }
// Start button GPIO and setup SPI for screen and SD card void begin();
// Button input methods void update(); bool isPressed(uint8_t buttonIndex) const; bool wasPressed(uint8_t buttonIndex) const; bool wasAnyPressed() const; bool wasReleased(uint8_t buttonIndex) const; bool wasAnyReleased() const; unsigned long getHeldTime() const;
// Setup wake up GPIO and enter deep sleep void startDeepSleep();
// Verify power button was held long enough after wakeup. // If verification fails, enters deep sleep and does not return. // Should only be called when wakeup reason is PowerButton. void verifyPowerButtonWakeup(uint16_t requiredDurationMs, bool shortPressAllowed);
// Check if USB is connected bool isUsbConnected() const;
// Returns true once per edge (plug or unplug) since the last update() bool wasUsbStateChanged() const;
enum class WakeupReason { PowerButton, AfterFlash, AfterUSBPower, Other };
WakeupReason getWakeupReason() const;
// Button indices static constexpr uint8_t BTN_BACK = 0; static constexpr uint8_t BTN_CONFIRM = 1; static constexpr uint8_t BTN_LEFT = 2; static constexpr uint8_t BTN_RIGHT = 3; static constexpr uint8_t BTN_UP = 4; static constexpr uint8_t BTN_DOWN = 5; static constexpr uint8_t BTN_POWER = 6;};
extern HalGPIO gpio;